Glossy exterior paint; water-based, silicone modification, styren acrylic copolymer emulsion based, glossy looking, exterior top coat paint.

Areas of use: It is applied as a top layer on surfaces such as concrete, plaster and chipboard.

Applicable surfaces : Concrete, plaster, chipboard, etc.

  • Thanks to its high strength strength, it integrates with the surface.
  • It is resistant to UV rays and does not fade.
  • It is resistant to severe climatic conditions.
  • It prevents possible microcracks that may occur on the surface.
  • It has excellent coverage.
  • Easy to apply with roller and spraying.
  • If applied correctly, spillage does not swell.
  • Surfaces to be applied; It should be clean, dry, dust-free, sturdy and in a position to carry itself.
  • In the priming process, the surface that is subjected to the priming process before the high-adherence power grainy, Silicone Primer paint should be made ready for painting.

Colors: Exterior Color Catalog.

pH Value : 8 – 9.

Final appearance : Semi-shiny and elastic.

Theoretical coating value : Depending on the condition of the surface to which it is applied, it is approximately 12 m
– 15 m² / L on a single floor.

Flash point : It is flammable and non-flammable.

Specific gravity : Approximately,1,50 – 1,60 gr/cm³.

Drying time : Approximately 30 – 40 minutes at 20 ºC

Viscosity : 130 KU (at 25 ºC)

Application Methods : It is applied with a brush or roller.

Thinning: Thinned with clean water (20% for the first floor, 10% for the second floor)

Cleaning of application tools: With clean water.

Required dry film thickness : Approximately 70 – 80 microns. (on two floors)

Required wet film thickness : Approximately 50 microns. (on one floor)

Waiting time between two layers : 2 – 4 hours.

Full drying time : 24 hours.

Consumption : 12 -15m2/L

  • Controlled sample is recommended for precise consumption.
  • During the application, the ambient temperature should be between +5°C and +30°C.
  • The values given above apply to environments with a relative humidity of 25 ºC and less than 70 %.

Packaging types: : 7,5lt,15lt plastic packaging.

  • It must be stacked up to a maximum of 3 times in its original packaging.
  • It should be stored indoors.
  • Necessary precautions should be taken against water, humidity, frost and severe weather conditions.
  • It should be stored on pallets and in dry places between +10°C and +25°C. Punctured, opened and exploded buckets should be closed or used immediately. If the specified storage conditions are complied with, the storage life is 24 months.
  • Thinning should be carried out at the recommended rate and it should be observed.
  • In applications with quantity and continuity, special attention should be paid to thinning at the same rate in order to avoid any difference in tone.
  • Avoid applying at temperatures below +5°C and above +35°C, do not try to use it by adding water to frozen material.
  • In case of application other than the necessary precautions and warnings in the application instructions described above, our company may suffer from application errors; SAPPHIRE PAINT is not responsible.
  • The rates specified are in theoretical standards and may vary according to the application method and intensity of use.
  • S 2 Keep out of the reach of children.
  • S 3/7/9 Store the box well closed, in cool and well-ventilated places.
  • S 16 Keep away from igniting sources.
  • S 23 Do not inhale Gas/Smoke/Vapor/Aerosol.
  • S 24/25 Avoid eye and skin contact.
  • S 26 In case of contact with eyes, immediately block with plenty of water, immediately consult a doctor.
  • S 28 Upon contact with the skin, immediately wash off with plenty of water.
  • S 29 Do not empty into the sewer.
  • S 37 Use appropriate protective gloves.
  • S 46 If swallowed, consult a doctor immediately, show the packaging or label.
  • S 51 Use only in well-ventilated areas.
  • During the application of processes such as sandblasting and burning on painted surfaces, harmful dust and / or smoke may be released, work in well-ventilated places.
  • Use appropriate personal protective equipment when necessary.
  • Upon request, a Safety Data Sheet (MSDS) and/or Technical Bulletin may be requested for detailed information.