GROUND CONCRETE PRIMER

Gross concrete lining, water-based, styren acrylic copolymer emulsion based, matte appearance, used to increase the adherence of the surface, to ensure maximum adhesion of coatings such as putty to the surface and to obtain a rough surface

Areas of Use: It can be applied on exterior structural elements such as concrete, gross concrete, mineral surfaces; to obtain rough surfaces.

Applicable surfaces: It is applied to the surface of concrete and gross concrete.

PRODUCT FEATURES:
  • Thanks to its spreading feature, it penetrates the surface quickly.
  • Thanks to its high strength strength, it integrates with the surface.
  • It is resistant to severe climatic conditions.
  • It prevents possible microcracks that may occur on the surface.
  • It is easy to apply.
  • It prevents rapid water loss in cement and gypsum based plasters.
  • If applied correctly, spillage does not swell.
  • It builds a binding bridge between the plaster and the surface.
  • It greatly prevents water and moisture permeability.
  • Increases the strength life of the plaster.
  • The surfaces to be applied as Gross Concrete Primer are robust, free from moving and weak parts, free from frost, cement sorbet, ponded water, oil, grease, paraffin, coatings, etc. it must be clean and dry, removed from impurities and other pollutants.

Colors: White, green, blue, etc.

pH value : 8 – 9.

Final view : Matt.

Theoretical coating value : Depending on the condition of the surface on which it is applied, on a single layer it is approximately 6 – 9 m
2
/L.

Flash point : It is flammable and non-flammable.

Specific gravity : Approximately,1,65 – 1,75 gr/cm
3
.

Drying time : Approximately at 20 ºC. It is 30 – 40 minutes.

Viscosity: It is not measured.

Application Methods : It is applied with a brush or roller.

Thinning: It is diluted with clean water. (% 30 – % 50)

Cleaning of application tools: With clean water.

Required dry film thickness : Approximately 50 microns (on one floor)

Required wet film thickness : Approximately 50 – 100 microns (in one layer)

Standby time between two layers : 30 – 40min

Full drying time : 24 hours.

Theoretical Consumption : 7 -10 m2/ L.

  • Controlled sample is recommended for precise consumption.
  • During the application, the ambient temperature should be between +5°C and +30°C.
  • The values given above apply to environments with a relative humidity of 25 ºC and less than 70 %.

Packaging types: : 3,5kg,10kg,20kg plastic packaging.

  • It must be stacked up to a maximum of 3 times in its original packaging.
  • It should be stored indoors.
  • Necessary precautions should be taken against water, humidity, frost and severe weather conditions.
  • It should be stored on pallets and in dry places between +10°C and +35°C.
  • Punctured, opened and exploded buckets should be closed or used immediately.
  • If the specified storage conditions are complied with, the storage life is 24 months.
  • Thinning should be carried out at the recommended rate and it should be observed.
  • In applications with quantity and continuity, special attention should be paid to thinning at the same rate in order to avoid any difference in tone.
  • Avoid applying at temperatures below +5°C and above +35°C, do not try to use it by adding water to frozen material.
  • In case of application other than the necessary precautions and warnings in the application instructions described above, our company may suffer from application errors; SAPPHIRE PAINT is not responsible.
  • The rates specified are in theoretical standards and may vary according to the application method and intensity of use.
  • TS 7847
  • G Communiqué.
  • Public Works Pose No: 04.466/3
  • S 2 Keep out of the reach of children.
  • S 3/7/9 Store the box well closed, in cool and well-ventilated places.
  • S 16 Keep away from igniting sources.
  • S 23 Do not inhale Gas/Smoke/Vapor/Aerosol.
  • S 24/25 Avoid eye and skin contact.
  • S 26 In case of contact with eyes, immediately block with plenty of water, immediately consult a doctor.
  • S 28 Upon contact with the skin, immediately wash off with plenty of water.
  • S 29 Do not empty into the sewer.
  • S 37 Use appropriate protective gloves.
  • S 46 If swallowed, consult a doctor immediately, show the packaging or label.
  • S 51 Use only in well-ventilated areas.
  • During the application of processes such as sandblasting and burning on painted surfaces, harmful dust and / or smoke may be released, work in well-ventilated places.
  • Use appropriate personal protective equipment when necessary.
  • Upon request, a Safety Data Sheet (MSDS) and/or Technical Bulletin may be requested for detailed information.