Acrylic roll exterior cladding is a water-based, styrene acrylic copolymeremulsion based, silica grain-containing, matte looking, decorative exterior roll coating.

Areas of use: It is applied as a top coat coating on concrete, plaster, chipboard etc. surfaces and primer paints.

Applicable surfaces : Concrete, plaster, chipboard, drywall and plaster applied to the primed surfaces of the floors.

  • It is resistant to UV rays and does not fade.
  • It is resistant to severe climatic conditions.
  • It prevents possible microcracks that may occur on the surface.
  • It has excellent coverage.
  • Easy to apply with roll.
  • If applied correctly, spillage does not swell.
  • Surfaces to be applied; It should be clean, dry, dust-free, sturdy and in a position to carry itself.
  • In the priming process, the surface that is subjected to the priming process before the high-adherence power grainy, Silicone Primer paint should be made ready for painting.

Colors: Exterior color catalog.

pH value : 8 – 9.

Final view : Matt.

Theoretical coating value : Depending on the condition of the surface to which it is applied, the approximate consumption in one layer is 0.8 kg – 1.2 kg/m

Flash point : It is flammable and non-flammable.

Specific gravity : Approximately 1.75 – 1.87 g/cm

Drying time : It is approximately 30 – 40 minutes at 20 ºC.

Viscosity : 120 KU (at 38 ºC)

Application Methods : It is applied with a brush or roller.

Thinning: It is diluted with clean water. (maximum 1 – 2% if required)

Cleaning of application means: with clean water.

Required dry film thickness : Approximately 70 – 80 microns. (on two floors)

Required wet film thickness : Approximately 50 microns. (on one floor)

Waiting time between two layers : 2 – 4hours.

Full drying time : 24 hours.

Consumption : 0,8kg-1,2kg/m

  • Controlled sample is recommended for precise consumption.
  • During the application, the ambient temperature should be between +5°C and +30°C.
  • The values given above apply to environments with a relative humidity of 25 ºC and less than 70 %.

Packaging types: : 25kg plastic packaging.

  • It must be stacked up to a maximum of 3 times in its original packaging.
  • It should be stored indoors.
  • Necessary precautions should be taken against water, humidity, frost and severe weather conditions.
  • It should be stored on pallets and in dry places between +10°C and +25°C. Punctured, opened and exploded buckets should be closed or used immediately. If the specified storage conditions are complied with, the storage life is 24 months.
  • Thinning should be carried out at the recommended rate and it should be observed.
  • In applications with quantity and continuity, special attention should be paid to thinning at the same rate in order to avoid any difference in tone.
  • On surfaces with salt vomiting or at risk, before the application of primer;
  • After cleaning the surface with a damp brush, it is recommended to apply 1 part of the mixture of surface impregnation material and 1 part of water to the surface with a brush.
  • Avoid applying at temperatures below +5°C and above +35°C, do not try to use it by adding water to frozen material.
  • In case of application other than the necessary precautions and warnings in the application instructions described above, our company may suffer from application errors; SAPPHIRE PAINT is not responsible.
  • The rates specified are in theoretical standards and may vary according to the application method and intensity of use.
  • S 2 Keep out of the reach of children.
  • S 3/7/9 Store the box well closed, in cool and well-ventilated places.
  • S 16 Keep away from igniting sources.
  • S 23 Do not inhale Gas/Smoke/Vapor/Aerosol.
  • S 24/25 Avoid eye and skin contact.
  • S 26 In case of contact with eyes, immediately block with plenty of water, immediately consult a doctor.
  • S 28 Upon contact with the skin, immediately wash off with plenty of water.
  • S 29 Do not empty into the sewer.
  • S 37 Use appropriate protective gloves.
  • S 46 If swallowed, consult a doctor immediately, show the packaging or label.
  • S 51 Use only in well-ventilated areas.
  • During the application of processes such as sandblasting and burning on painted surfaces, harmful dust and / or smoke may be released, work in well-ventilated places.
  • Use appropriate personal protective equipment when necessary.
  • Upon request, a Safety Data Sheet (MSDS) and/or Technical Bulletin may be requested for detailed information.